CCO swing cab (TLL) practice test
TLL covers telescopic cranes where the operator rides in a cab that turns with the boom: rough-terrain cranes, all-terrains and hydraulic truck cranes.
15 Swing cab (TLL) practice questions with answers
Pick an answer to see whether you were right and why. Reviewed November 2026. No sign-up.
-
Swing Cab — General
1.During an on-rubber pick-and-carry (creep) move, the boom should be kept:
Show answer
Answer: A. centered over the front and low, with the load close to the ground. On-rubber travel is most stable with the boom centered over the front and the load carried low and close, in line with the direction of travel.
-
Swing Cab — General
2.Attaching and using the auxiliary boom head adds how much to the effective main boom length for chart purposes on many swing cab cranes?
Show answer
Answer: C. about 2 feet. The auxiliary head extends beyond the main boom tip, so roughly 2 feet is added to the boom length before entering the chart.
-
Swing Cab — General
3.The two-position travel swing lock used during on-rubber pick and carry:
Show answer
Answer: B. keeps the boom centered over the front during travel. The travel swing lock holds the upperworks so the boom stays over the front while the crane moves with a load.
-
Swing Cab — General
4.When lifting on outriggers, the outrigger beams on a swing cab crane must be:
Show answer
Answer: D. all set to the same extension (all in, all mid, or all out). All beams must match — fully retracted, an intermediate detent, or fully extended — to keep a balanced, charted footprint.
-
Swing Cab — General
5.The auxiliary (single-sheave) boom head is generally limited to:
Show answer
Answer: C. a single part of line. A single-sheave auxiliary head reeves only one part of line, so its capacity is capped by the single-part line pull.
-
Swing Cab — General
6.What is the "upperworks" (house) of a swing cab telescopic crane?
Show answer
Answer: D. The rotating superstructure carrying the boom, cab, hoist, and counterweight. The upperworks or house is the rotating superstructure; the carrier (lowerworks) is the chassis beneath it.
-
Swing Cab — General
7.On a swing cab crane, the operator's cab:
Show answer
Answer: B. rotates with the boom on the upperworks. The swing cab is mounted on the rotating superstructure, so the operator turns with the boom and keeps the load in view.
-
Swing Cab — General
8.The least stable working quadrant on a swing cab crane set on outriggers is generally:
Show answer
Answer: D. over the side. Over the side is usually the least stable quadrant because the outrigger footprint is narrowest in that direction.
-
Swing Cab — General
9.On a rough terrain (swing cab) crane, capacities are generally greatest:
Show answer
Answer: C. over the front. RT cranes typically rate highest over the front, where the outrigger base and frame brace best — always confirm with the work-area chart.
-
Swing Cab — General
10.Extending the outrigger beams from the upper cab, the operator should:
Show answer
Answer: D. maintain visual contact with the outrigger or use a spotter. Because the beams are out of easy view, the operator must watch them directly or use a spotter so no one is struck and the beams deploy fully.
-
Swing Cab — General
11.On a hydraulic truck-style swing cab crane, the 'over-the-front' working area is:
Show answer
Answer: C. defined by the crane manufacturer's work-area diagram. The boundaries of each working area, including over-the-front, are set by the manufacturer's work-area diagram for that specific crane.
-
Swing Cab — General
12.When telescopic sections that must extend equally become uneven, the danger is that:
Show answer
Answer: A. the section extended furthest carries more than its designed load. An unequal extension overloads the most-extended section in bending and can cause structural boom failure.
-
Swing Cab — General
13.The primary reason all outrigger beams must be at equal extension is to:
Show answer
Answer: C. keep the tipping fulcrum symmetric and match the published chart. Unequal beams create an unsymmetric, uncharted footprint that can tip toward the short side.
-
Swing Cab — General
14.Which working-area quadrant of an RT swing cab crane is normally strongest?
Show answer
Answer: A. over the front. Rough terrain cranes generally publish their highest capacities over the front.
-
Swing Cab — General
15.Placing the load on the uphill side when carrying on a grade is important because downhill placement:
Show answer
Answer: C. increases the radius and can tip the crane. Downhill of the crane the effective radius lengthens, reducing capacity and threatening a tipover.
You scored
That was 15 swing cab (tll) questions. The app has the full bank, tracks every miss and brings it back until you have it.
What the Swing cab (TLL) exam covers
- Outrigger extension and setup
- Working quadrants and stability
- On-rubber and pick-and-carry limits
- Auxiliary boom head and jib use
- Telescoping sequence and boom modes
- Swing cab load chart deductions
| Exam | Questions | Time | Calculator | Fee |
|---|---|---|---|---|
| Core written (all mobile cranes) | 95 | 90 min | No | $140 |
| TLL specialty written | 28 | 60 min | Yes | $80 |
| TLL practical | — | — | — | $70 |
Exam format from the CCO Mobile Crane Operator Candidate Handbook. Fees from the CCO fee schedule.
Study the whole Swing cab (TLL) exam
5,000+ practice questions across core and every specialty, timed practice exams, a load chart trainer and audio lessons. One payment of $197 covers 12 months.
Swing cab (TLL) exam questions
How many questions are on the CCO TLL written exam?
28 questions with a 60-minute limit, and a calculator is allowed. To earn the TLL designation you also pass the 95-question core exam and the TLL practical.
What does the TLL written exam cover?
Four areas: site (about 23%), operations (about 23%), technical knowledge (about 19%) and load charts (about 35%). The load chart problems use the manufacturer charts handed out with the exam.
What does the TLL exam cost?
CCO lists $80 for the TLL written exam and $70 for the TLL practical, plus $140 for the core written exam if you have not passed it.
What is the difference between TLL and TSS?
TLL is the swing cab: the cab rotates with the upper. TSS is the fixed cab: the operator station stays on the carrier, as on most boom trucks and carry deck cranes.
Are these the real CCO exam questions?
No. CCO does not publish its exam questions. These are original practice questions on the same swing cab topics, each with the rule or reason behind the answer.