Free 25-question CCO practice test with answers. No sign-up. Start now
RIG · Free practice test

CCO rigger practice test

Rigger Level I covers rigging a load when the weight and center of gravity are known. Level II adds working those out yourself and choosing the rigging.

60Level I questions
50Level II questions
60 mineach exam
$105written fee

20 Rigger practice questions with answers

Pick an answer to see whether you were right and why. Reviewed November 2026. No sign-up.

Not started20 to go
  1. Rigging 1

    1.For which loads is a single vertical hitch acceptable?

    Show answer

    Answer: A. Only items equipped with lifting eye bolts or shackles, such as concrete buckets. A single vertical hitch carries the total load on one leg at a 90-degree angle and can equal the sling's maximum safe working load, but it must not be used for loose material, lengthy material, or hard-to-balance loads — it provides absolutely no control because it permits rotation.

  2. Rigging Hardware

    2.The main penalty of SQUARE reeving a set of blocks is:

    Show answer

    Answer: C. Continual reverse bending of the rope, plus blocks that cannot be brought close together. Square reeving runs smooth and level, but the rope is bent back and forth continually, which brings on fatigue, and the block positions stop them closing up (forcing lines off the sheaves at excessive angles if you try).

  3. ASME B30.9 (Slings)

    3.Which fiber rope material floats on water?

    Show answer

    Answer: A. Polypropylene. Polypropylene (specific gravity about .91) floats; manila, sisal, nylon and polyester all sink.

  4. Rigging 2

    4.When a line passes around a block and doubles fully back on itself (a 0-degree full included angle), the load on the block equals:

    Show answer

    Answer: A. 2 times the line pull. Block load = block factor x line pull; the block factor is 2.00 at 0 degrees, 1.41 at 90 degrees, 1.00 at 120 degrees, and 0 at 180 degrees.

  5. Rigging 1

    5.Which hitch attachment will provide 360-degree contact and pulls the load together?

    Show answer

    Answer: C. A double wrap choker hitch. A double wrap choker passes the sling completely around the load before choking, giving full 360-degree contact that compresses and binds loose or bundled material together.

  6. ASME B30.9 (Slings)

    6.What is the temperature use range limit for polyester and nylon rope, webbing, and polyester roundslings?

    Show answer

    Answer: D. Not above 194°F (90°C) or below -40°F (-40°C). Sections 9-4.8.1, 9-5.8.1, and 9-6.8.1 all prohibit use in contact with objects or at temperatures above 194°F (90°C) or below -40°F (-40°C).

  7. Rigging 2

    7.To develop the full published basket hitch rating, what minimum D/d ratio is required for extra-extra improved plow (EEIPS) wire rope slings, compared with improved and extra improved plow?

    Show answer

    Answer: D. 20 to 1 for EEIPS, versus 25 to 1 for IPS and EIPS. Basket ratings assume a generous bend around the load. IPS and EIPS need 25:1; EEIPS constructions are credited at 20:1. Below the required ratio the tabulated basket capacity must be reduced.

  8. Blocks, Hoists & Pulling Gear

    8.On a wire rope block, what is the function of the cheek straps?

    Show answer

    Answer: A. They carry load between the end attachments and the sheave center pins. Cheek straps are the structural path from the block's end fittings to the sheave center pins, which is why wire rope blocks can be much lighter than hook blocks of similar capacity.

  9. Rigging 1

    9.Besides stretch and cracks, an alloy chain sling is removed from service for...

    Show answer

    Answer: B. Nicks, gouges, or wear that reduce a link's cross-section beyond the manufacturer's limit. Deep nicks, gouges, and wear remove metal from the link cross-section and reduce strength; when they exceed the manufacturer's allowable wear the sling is retired.

  10. Rigging Hardware

    10.A rigger terminates ROTATION-RESISTANT rope in a wedge socket with a dead-end tail of 6 rope diameters. This tail is:

    Show answer

    Answer: D. Too short — rotation-resistant rope requires at least 20 rope diameters (never less than 150 mm). Trap: rule borrowed from the wrong rope — 6 diameters is the standard 6-to-8-strand minimum; rotation-resistant rope needs 20 diameters and never less than 150 mm.

  11. ASME B30.9 (Slings)

    11.What do exposed "Red Guard" red threads in a web sling indicate?

    Show answer

    Answer: D. The manufacturer recommends removal from service even though this is not in OSHA/ASME criteria. Some manufacturers weave red threads into the inner webbing layer; if they are ever exposed, the sling should be removed from service, a recommendation beyond the ASME/OSHA removal lists.

  12. Rigging 2

    12.A reinforced-concrete block measures 4 ft x 4 ft x 3 ft. Using 150 lb per cubic foot, what does it weigh?

    Show answer

    Answer: A. 7,200 lb. Volume = 4 x 4 x 3 = 48 cu ft; 48 x 150 = 7,200 lb.

  13. Blocks, Hoists & Pulling Gear

    13.When counting parts of line for mechanical advantage, how is the lead line treated?

    Show answer

    Answer: C. Not counted if it comes down over the top block, but counted if it comes up from the travelling block. Only lines that actually support the travelling block count. A lead line dropping off the top block just changes direction, but a lead line leaving the travelling block upward carries load and adds a part.

  14. Rigging 1

    14.When a NON-fiber core wire rope sling is used at temperatures above 400 degrees F or below minus 60 degrees F, what is required?

    Show answer

    Answer: B. Follow the sling manufacturer's recommendations for use at that temperature. Outside the 400 degrees F to minus 60 degrees F window, nonfiber core wire rope slings may be used only per the sling manufacturer's recommendations.

  15. Rigging Hardware

    15.How must a duplex (sister) hook normally be loaded?

    Show answer

    Answer: A. Equally on both sides, unless specifically designed for single-point loading. Duplex hooks must be loaded equally on both sides unless the hook is specifically designed for single-point loading.

  16. ASME B30.9 (Slings)

    16.In manila rope, OSHA requires eye splices to consist of at least how many full tucks?

    Show answer

    Answer: C. Three. Manila eye splices need at least three full tucks (short splices six); synthetic fiber rope eye splices need at least four full tucks (short splices eight, four each side of the centerline).

  17. Rigging 2

    17.In the rated capacity formula RC = (MBF x L x Sin A) / DF x NSE, what does Sin A represent?

    Show answer

    Answer: D. The sine of the smallest horizontal sling angle. Sin A is the trigonometric sine of the smallest horizontal sling angle; MBF is minimum breaking force, L the number of legs, DF the design factor, NSE the nominal splice efficiency.

  18. Blocks, Hoists & Pulling Gear

    18.What does reeving MORE parts of line trade away in exchange for capacity?

    Show answer

    Answer: B. Hoisting speed — the hook moves slower for the same rope speed. Every extra part multiplies force but divides hook speed: at 6 parts the drum spools six feet of rope for every foot the hook rises.

  19. Rigging 1

    19.In a double basket hitch, what minimum angle between the load and the sling should be maintained to avoid slippage?

    Show answer

    Answer: B. Approximately 60 degrees or greater. The angle between the load and the sling should be approximately 60 degrees or greater to avoid slippage, and the legs must be far enough apart for balance but not so far that excessive angles pull the legs toward the center. On smooth surfaces, snub the hitches against a step or change of contour.

  20. Rigging Hardware

    20.What is the correct way to keep a load centered on a shackle pin when the fitting is narrower than the shackle?

    Show answer

    Answer: A. Pack the pin with washers to centralize the shackle. Packing the pin with washers centralizes the load on the shackle and prevents eccentric loading that spreads the legs.

What the Rigger exam covers

  • Hitches and when each one fits
  • Sling materials and temperature limits
  • Shackles, hooks and wedge sockets
  • Blocks, reeving and parts of line
  • Load weight calculations
  • Removal-from-service criteria
ExamQuestionsTimeWritten feePractical fee
Rigger Level I6060 min$105$95
Rigger Level II5060 min$105$95

Exam format from the CCO rigger program. Fees from the CCO fee schedule.

Study the whole Rigger exam

5,000+ practice questions across core and every specialty, timed practice exams, a load chart trainer and audio lessons. One payment of $197 covers 12 months.

Rigger exam questions

How many questions are on the CCO rigger exams?

Rigger Level I has 60 multiple-choice questions in 60 minutes. Level II has 50 questions in 60 minutes.

Do I need Level I before Level II?

Level II is only valid while your Level I certification is current, so in practice you hold both.

What does CCO rigger certification cost?

CCO lists $105 for each rigger written exam and $95 for each practical.

Are these the real CCO exam questions?

No. CCO does not publish its exam questions. These are original practice questions on the same rigging topics, each with the rule or reason behind the answer.

More free CCO practice tests

5,000+ questions in the app.Get full access